Artificial Grass Installation Thousand Oaks – Have You Ever Asked Myself The Reason Why You Absolutely Need This..

When you have completed the preparation stage which include measuring exactly how much artificial grass you need, installing appropriate drainage (if needed) and eliminating the natural grass layer, you will be ready to install your artificial grass lawn. This article outlines the steps you should follow to assist you to do the job right, from laying the base, connecting joints and protecting against unwanted weeds.

Lay Gravel Base then Sharp Sand – If neccessary, use treated timber/timber stakes to put inside an area frame. We recommend 4 X 2 inches of tantalised treated timber for heavy clay soil areas and poorly draining areas and 2 X 2 inches of tantalised timber for good draining areas. Screw these timbers towards the stakes leaving the stakes on the inside of the perimeter. In case the Artificial Grass meet a concrete path, wall or decking, position the timber flush with the surface height and also by using 10mm temporary fillet, pack the timber close to the wall leaving the room to enable you to tuck the Artificial Grass involving the timber as well as the adjoining material with a later stage.

Position the stakes up against the inner perimeter timber edging and hammer into the ground ensuring the stakes are slightly below the timber edging. Next screw the timber stake towards the timber edging. With heavy clay soils we recommend laying a crushed stone surface as high as 3 inches. This will never be necessary for the majority of areas and merely required for those who have a higher water table in which the ground holds water for long periods of time after it rains. Next compact the ground using a vibrating plate that can be hired from an equipment hire company. Guarantee the perimeter is compacted and below the timber edging by 1 inch. Infill the perimeter with sharp sand and level utilizing a rake. Make sure the sand is level to the peak in the timber edging and compact again.

Permanently drainage areas spread a layer of sharp sand to blind on the soil. Next compact the ground utilizing a vibrating plate which can be hired from an equipment hire company. Guarantee the perimeter is compacted and level with the timber edging. If you put more work in at this point, your Artificial Grass Lawn will appear better because of this.

Weed Control Layer – Apply the weed control geo textile membrane and cut as necessary. Tack using small 1 inch galvanised clout nails to the timber edging. This weed control geo textile membrane prevents any chance of weed growth with the artificial grass drainage holes.

Roll out Artificial Grass – Lay the Artificial Grass within the desired direction working on the carpet and not on the levelled base. Ensure the carpet is positioned to minimise cuts, joints and waste overlaying the timber edging by at least 4 inches. When the artificial grass meets a path or edge, and for those who have laid the timber edging correctly as previously described, then the artificial grass may be wedged between. If joining, please be sure that the artificial turf cost thousand oaks is laid using the pile running in the same direction on every piece. Lay the carpet on top of the sand rather than dragging it across the base material. To aid stop wrinkles or creasing you should allow 2 to three hours to settle before continuing with jointing and adhesive. Cut grass to shape using a sharp Dolphin or Stanley knife or scissors.

Jointing – When jointing your outdoor carpet together, ensure the pile runs within the same direction. Stop manufacturer’s edge strip (if present) and butt two edges together ensuring there are no gaps more than 1mm in between the two carpet edges. The precision with this determines how visible the join is after the completion. Fold back edges and position jointing tape (smooth side down) in order that the edges from the carpet satisfy the tape when joined.

Adhesive – a) Apply the cartridge adhesive in a zig zag motion onto the rougher side from the tape allowing one cartridge for each 3 linear metres. Reject carpet and press both edges into the wet adhesive, ensuring every piece marries up and has no overlap. Since you are doing this together with your fingers, mix the fibres together to conceal the join. When the whole length is within place and you also are satisfied with its appearance it is actually essential to walk along the join several times to activate the glue and bond the grass to the tape. Weigh on the seam to ensure good connection with the glue until it cures. The greater care taken with the operation the neater and tidier the joint is going to be.

b) If utilizing the 2-component multi-purpose adhesive, ensure thorough mixing of the two components before use. Apply adhesive towards the rough side in the tape and spread evenly across a width of at the very least 20cm using when possible a notched trowel. Sufficient adhesive should be applied to ensure that if the artificial grass carpet is pressed into the adhesive, a transfer over the xggnvo backing is complete. Reject carpet and press both edges in to the wet adhesive, ensuring every piece marries up and it has no overlap. Ensure that the carpet does not crest at the seam and it is holding flat within the bonded area. After the whole length is in place and also you are satisfied featuring its appearance it is necessary to walk across the join many times to activate the glue and bond the grass for the tape. Weight the seam to make certain good exposure to the glue until it cures. The more care taken using the operation the neater and tidier the joint is going to be.

As you should endeavour never to put adhesive onto the carpet small quantities of glue can be removed from the artificial grass fibre using White Spirit as well as a small off cut of the artificial grass. Small quantities of cured glue normally can be removed. To prevent this situation and the potential of harm to the artificial grass, care and precautions ought to be come to avoid contact with the fibres at all times. If the artificial grass has been jointed and glued and also you are pleased using the levels screw the grass to the timber perimeter framework using galvanised screws at the very least of 12 inch intervals.

Spread Sand (Optional, according to Grass Selected) – When the artificial grass has become laid use silica sand, that is kiln dried and brush into carpet as you go. Each product could have sand infill but this is only employed to stabilise the carpet and at no time should the sand be visible. You must obtain an even spread within the surface using a brush to build up the depth in layers. Do not apply the sand in a single application. Brush sand into pile soon after laying whilst the artificial grass is dry and while weather is good. Brush vigorously against the fibres of the carpet pile to encourage the tufts to stand upright. Putting the correct level of sand in helps support the artificial grass to bed down, protects the fibres and in addition keeps them standing allow it the appearance of real grass.

Leave a Reply

Your email address will not be published. Required fields are marked *